二维码入口
帮助中心
高级搜索:
当前位置:丝印特印网 > 产品信息 > 产品供应 > 单组份自干玻璃油墨单组份免固化剂油墨
上海凯贤印刷科技有限公司
产品分类
  金属油墨
  PP油墨
  电木油墨
  电泳油墨
  亚克力油墨
  UV油墨
  五金油墨
  陶瓷油墨
  ABS油墨
  HIPS油墨
  线路板油墨
  电镀油墨
  玻璃油墨
  PE油墨
推荐产品
电泳表..
 
胶木移..
 
胶木丝..
 
电木移..
 
电木丝..
 
耐黄油..
 
耐植物..
 
耐动物..
 
耐热油..
 
耐高温..
 
丝印五..
 
亚克力..
 
强化P..
 
强化亚..
 
耐汽油..
 
耐酒精..
 
移印亚..
 
丝印亚..
 
电泳表..
 
五金表..
 
丝印自..
 
耐冲压..
 
耐汽油..
 
耐酸碱..
 
耐酒精..
 

单组份自干玻璃油墨单组份免固化剂油墨

分享到:
订货量:
价格(不含发票):
1
180元/kg
产品类别:
油墨颜料
供应数量:
不限
有 效 期:
0
发布时间:
2018-07-20
所 在 地:
上海
联 系 人:
黄奕宸
详细信息
联系方式

“单组份自干玻璃油墨”欧莱斯油墨

1、 适用材质:金属、电镀、氧化铝、电解板、铝塑板、喷(烤)漆、喷塑、PA塑料尼龙、电木、玻璃钢、密胺等。


2、 产品特性:半光、免烘烤、耐酒精、耐冲压。


3、 稀释剂:本公司B-03稀释剂或783慢干稀释剂。


4、 固化剂:本产品为单组份油墨,如有特殊要求也可选择添加固化剂增加附着力及墨层抗性。


5、 油墨调配:充份搅拌后取所需用量进行调配使用,双组份油墨先按比例添加固化剂搅拌均匀,然后再添加稀释剂稀释到合适粘度进行印刷;添加固化剂后的油墨超过使用时限会产生粘稠胶化现象,请及时清洗网版,并弃用油墨,不可回收。


6、 网版及刮胶:适合80T-140T(200目-350目)聚脂网纱,聚氨脂PU油性刮胶。


7、 干燥条件及时间:本产品可以常温干燥,也可以烘烤快速干燥,建议干燥温度及时间为25℃/24小时,60℃/40分钟,80℃/30分钟,100℃/20分钟。


8、 性能检测:

用3M600胶带划百格测试100%无脱落;

用棉布沾95%工业酒精以500G力水平来回擦拭100次无脱色;

1mm厚铝片在印刷位置进行冲断、卷边、延压后边缘位置100%无脱落;


9、 包装规格:1KG/胶罐,12罐/箱。


10、储存条件:置于干燥通风处常温保存;避免高温、太阳直射,严禁烟火。


11、注意事项:请向我司索取《MSDS安全使用手册》,并按指引进行安全生产。?

Glass screen printing resistant acid and alkali ink


1, applicable materials: metal, electroplating, alumina, electrolytic plate, aluminum plate, spray paint, spray (baked), PA nylon, bakelite plastic, glass steel, melamine etc..


2, product characteristics: half light, no baking, alcohol resistance, stamping.


3. Diluent: the company's B-03 diluent or 783 slow dry diluent.


4, curing agent: This product - ink, if there are special requirements can also choose to add curing agent to increase adhesion and ink layer resistance.


5, ink deployment: fully mixing after the dosage required for the deployment, two-component ink first adding curing agent according to the proportion of mixing evenly, then add the diluent to the appropriate viscosity of printing ink; curing agent is added after more than the use of time will produce viscous gel phenomenon, please clean the screen, and abandoned ink Unrecyclable.


6, screen and frictioning: for 80T-140T (200 -350 mesh) polyester mesh, polyurethane PU oily frictioning.


7, drying conditions and time: This product can be dried at room temperature or dry quickly. It is recommended that the drying temperature and time should be 25 /24, 60 /40, 80 /30, 100 /20.


8. Performance testing:

Use 3M600 tape to make 100 lattice tests 100% without falling off.

With cotton cloth, 95% industrial alcohol was wiped back and forth at the level of 500G force for 100 times without decolorization.

The position of 1mm thick aluminum sheet in the printing position is broken, curling, and the edge position after the pressure is 100% without falling off.


9, packaging specifications: 1KG/ glue cans, 12 cans / boxes.


10. Storage conditions: keep at room temperature in the dry and ventilated place; avoid high temperature, direct sunlight, and strictly prohibit fireworks.


11, attention: please ask our department "MSDS safety manual" and carry out safety production according to the guidelines.



联系方式
公司名称:
上海凯贤印刷科技有限公司
联 系 人:
黄奕宸
电  话:
18074309897
手  机:
18074309897
传  真:
021-59507952
地  址:
  
Q   Q:
QQ交谈
还没有找到合适的产品? 赶快发布求购信息,让供应商主动来找您!收藏此信息
免责声明:以上信息由会员自行提供,内容的真实性、准确性和合法性由发布会员负责。丝印特印网对此不承担任何责任。
联系我的时候!请说明在丝印特印网上看到的,我好做备案!